Banks-power Chevy_GMC Trucks: Duramax LLY-LBZ (Diesel ’06 - 07 Manuel d'utilisateur

02/28/12 PN 97246 v.3.0©2012 Gale Banks EngineeringBanks Brake®Compatible with Installed Six-Gun® Power Tuner with Six-Gun Switch2006-2007 Chevy/GMC

10 97246 v.3.05. Secure the wire harness using some of the supplied cable ties along the factory wire harness up the left side of the engine to the

97246 v.3.0 1114. Install the mini-blade fuse tap onto the removed mini fuse as shown in Figure 8. Re-install the mini fuse with the attached blade

12 97246 v.3.0Figure 7 Electrical Center Fuse Tap LocationFigure 8 Fuse Tap Installation

97246 v.3.0 13Figure 9If a Banks Diesel Tuner has been previously installed, skip step 20.19. Locate the rubber grommet on the driver’s side of the

14 97246 v.3.0Figure 10 Driver Side Firewall, Rubber GrommetFigure 11

97246 v.3.0 15Figure 13 Placement of Banks Tuner on side of the Fuse Box.Figure 12 Placement of Banks Tuner on top of the Fuse Box.

16 97246 v.3.0WARNING: Make sure to place the Banks Brake Module as shown in Figure 11 to avoid a clearance issue when closing the hood. Mount the S

97246 v.3.0 17CAUTION: Do not use force when working on plastic parts. Permanent damage to the part might result.1. The Banks Brake switch will be i

18 97246 v.3.0Figure 17Figure 16

97246 v.3.0 196. After confirming the locating washer is in the #5 location, install the switch through the 3⁄8” hole on the backside of the instrum

2 97246 v.3.0Do not use this product until you have carefully read the following agreement.This sets forth the terms and conditions for the use of t

20 97246 v.3.0Section 3BANKS BRAKE OPERATIONThe Banks Brake has five (5) operating settings; HIGH, MED (medium), LOW, OFF and FB (Foot Brake Activat

97246 v.3.0 21OPERATION/DRIVINGNow that you are familiar with the features that are available with Banks Brake, it is recommended that you experimen

22 97246 v.3.0Flash CodePDA Error Message Corrective Action- LBZ/ LMM1.1 Code 11: VGT control input out of rangeTurn ignition OFF and check the 24-P

97246 v.3.0 23LED separates the sequences. The LEDs will continue to ash to display all the errors, and then repeat. Table 1 lists the common diagn

Gale Banks Engineering 546 Duggan Avenue • Azusa, CA 91702 (626) 969-9600 • Fax (626) 334-1743Product Information & Sales: (888) 635-4565bankspowe

97246 v.3.0 3and must be accompanied by a dated proof of purchase receipt. All Warranty claims are subject to approval by Gale Banks Engineering Inc

4 97246 v.3.0Banks iQ System(P/N 61141-61145)- 5” touchscreen interface that can control the Banks Diesel Tuner and/or SpeedBrake on the fly.- Inter

97246 v.3.0 5Big Hoss Intake Manifold System(P/N 42733)- Increases flow and provides more uniform air distribution to the engine for more available

6 97246 v.3.0Dear Customer,Your new Banks Brake is a uniquely designed braking system with electronic controls, designed to achieve the optimum leve

97246 v.3.0 7Section 1INSTALLATION OF BANKS SPEEDBRAKE WIRE HARNESSFigure 1 Banks SpeedBrake and supplied wiring harness

8 97246 v.3.0NOTE: If you have purchased a combination Banks Brake/ Tuner Package, install the Tuner First and ignore the installation of the OBD II

97246 v.3.0 9Figure 4Figure 3 Remove of Driver Side Cowl Support Brace